iPadAir2 LCD glass panel replacement repair and disassembly method 7 steps in all




how to repair and disassemble iPadAir2 LCD cracks, display defects, cracks, cracks, cracks

Leave the ipad repair to us

iPadAir2 LCD glass panel replacement and disassembly procedure

[iPadAir2 LCD glass panel replacement STEP 1]
ipad air Disassembly Method 1
This is an effective decomposition method when the iPadAir2 touch panel (LCD glass) is broken, display is defective, lines are in place, or partially invisible.
Decomposition from iPadAir2 has become very delicate, so if you feel it is difficult to see the following contents, please consult the repair shop without hesitation!
In this decomposition, only the screen is not cracked, but even if it is cracked, how to remove it will be the same, so please check the contents.
We will remove the liquid crystal from now on, but the liquid crystal stops with a strong double-sided tape on the main body side.
As for the flow to remove the liquid crystal, it is impossible because it is very hard to pull it out as it is though it only pulls it out to the front side.
Apply a dryer or heat gun around the LCD to soften the double-sided tape on the inside before removing it.
[iPadAir2 LCD glass panel replacement STEP 2]
In the image, we use tools, but this is called suction cups and is mainly used by glass shops.
It is very difficult to remove the glass surface without warming it with this tool.
If you take the time to repeat the work of floating with heat, you will see that it floats a little.
If you can check the Kuta thing floating even a little card in the gap, let's pack the thin thing, such as a pick!
We use a pick in the image, but there is a liquid crystal panel when the tip enters 4mm, so it is not possible to insert any more.
So, please beless than 4mm when inserting.
This work is carried out one lap around the liquid crystal.
[iPadAir2 LCD glass panel replacement STEP 3]
It is a direction to peel off, but it is also possible to wake up to the lower side using the hand if it is possible to peel off the left and right to some extent.
Please note that there is wiring just to the right of the home button.
[iPadAir2 LCD glass panel replacement STEP 4]
I think that I could see the inside of the iPadAir2 if I could completely wake up the LIQUID CRYSTAL.
The image part is a battery connector and a liquid crystal cable.
Remove the battery connector before removing the cable, but be sure to do this first.
If you remove the screw of the red circle part, it will float slightly, so if you insert a pick etc. into the gap, electricity will not flow to the iPad.
Next, remove the screw of the orange part, but if you can remove the screw, you will be able to remove the silver plate by hand.
[iPadAir2 LCD glass panel replacement STEP 5]
ipad air disassembly method 8
I was able to check the wiring of the liquid crystal.
You can remove the connector if you try to lift it from the bottom to the top, but if you remove one, the connector will come out further down, so you will remove it in the same way.
[iPadAir2 LCD glass panel replacement STEP 6]
The LCD cable is removed.
I think that I was able to remove the liquid crystal with this.
In the case of the iPadAir of the first model, it was necessary to remove the home cable, but since it became Air2, the home button cable connected to the logic board is no longer available, so it became easier to work with.
[iPadAir2 LCD glass panel replacement STEP 7]
Only the liquid crystal was able to be removed from the main body.
In the case of liquid crystal replacement, the work is completed if it is incorporated according to the original procedure.
Since the lcd of the iPadAir2 is now a set of glass and panels, the liquid crystal change is easier than before, but the part fee is a little higher.
スポンサーリンク
スポンサーリンク



コメントを残す

メールアドレスが公開されることはありません。 * が付いている欄は必須項目です