NEC PC-LS150RSW-KS Liquid Crystal Repair and Decomposition Method 10 steps

NEC PC-LS150RSW-KS LCD Cracking Screen Replacement Repair Method, Decomposition Procedure

[NEC PC-LS150RSW-KS Liquid Crystal Repair and Decomposition Method STEP 1]: It is a state that the horizontal line, the crack, and the display defect have gone out by having hit the laptop.
If you end up with this symptom, you need to change the panel, but it's data that you're worried about, right?
Liquid crystal cracking is a PERSONAL computer trouble that occurs when suddenly, but there are many things that remain unexpectedly data, and there are many cases where it can be used in the state up to now if only the panel is replaced.
If you have an external monitor, you can check whether the data on the laptop side is left by using the D-SUB15 pin, HDMI terminal, etc.
I think that it is good to have you take the backup in this way when it is put out to the repair shop.
In this case, you can use the PC as soon as you replace only the panel because the data remained.

[NEC PC-LS150RSW-KS Liquid Crystal Repair and Decomposition Method STEP 2]: Be sure to remove the battery first when disassembling your laptop.
Please note that if you do not remove the battery and disassemble it, it may short down somewhere, and the power may not turn on.

[NEC PC-LS150RSW-KS LIQUID LIQUID REPAIR and Decomposition Method STEP 3]: Before removing the LaVie LS150/RSW-KS LCD panel, you need to remove the frame first.
The frame itself is fixed with two screws, and there is a screw in the red frame part, so let's remove it!

[NEC PC-LS150RSW-KS Liquid Crystal Repair and Decomposition Method STEP 4]: Because black rubber is attached like the image on the screw, it peels off with the one with the tip such as tweezers.
Please keep the rubber because it reuses it later.

[NEC PC-LS150RSW-KS Liquid Crystal Repair and Decomposition Method STEP 5]: If you can peel off the black rubber, you will see the screws, so you should use a Phillips screwdriver.
This is the left side, but there is a screw in the same way on the right side, so don't forget to remove it!

[NEC PC-LS150RSW-KS Liquid Crystal Repair and Decomposition Method STEP 6]: From here, we'll break down the frame.
It becomes the most difficult to understand decomposition by the liquid crystal panel exchange, but please disassemble carefully without rushing because it becomes a simple task except if you get the knack.
First, use a tool (plastic spatula) similar to the image to insert it into the gap between the rear panel and the frame.
It is the position to insert first, but I think that the upper left or the upper right is good.
The frame is fixed with plastic claws on the rear panel, but it is done with an image that decomposes the plastic model.
If you insert the spatula and make it light, there is a feeling that the nail comes off, so we will do this work throughout the liquid crystal.
Let's do it carefully because it comes to be able to remove the frame when the whole nail comes off!

[NEC PC-LS150RSW-KS Liquid Crystal Repair and Decomposition Method STEP 7]: I think that it became the state of the image if it was possible to remove the frame.
Since the panel itself is fixed with four screws, remove all the screws in the part that is enclosed in a red frame.
If you can remove the screw, the liquid crystal will move freely, so it will knock down to the keyboard side as it is.
Please do not disconnect because the liquid crystal cable is connected to the back when knocking down.

[NEC PC-LS150RSW-KS Liquid Crystal Repair and Decomposition Method STEP 8]: The LCD cable can be easily removed by sliding it.

[NEC PC-LS150RSW-KS LIQUID LIQUID REPAIR and Decomposition Method STEP 9]: It is a genuine panel of PC-LS150RSW-KS.
LP156WH3 (TL) (S1) was installed.

[NEC PC-LS150RSW-KS LIQUID LIQUID REPAIR and Decomposition Method STEP 10]: I replaced the new panel and turned it on, but I was able to confirm that it was displayed normally.