How to repair and disassemble the iPad Mini 4 LCD cracks, cracks, cracks, and screen scans
LCD replacement and decomposition procedure sianafor iPad Mini 4 8 steps
[iPad Mini 4 LCD Replacement STEP 1]
The lcd of the iPad Mini 4 is easy to remove other than because the glass and the panel are integrated like iPadAir2, Even in the case of glass cracking, it will be replaced by each liquid crystal panel, so it will be more expensive than the model that can only replace the glass.
I think that it does not take much time because the connector in the inside can be easily removed if only the liquid crystal of the surface can be removed.
The lcd of the iPad Mini 4 is only fixed with a good double-sided tape today, but it is very hard as it is, so if you use a heat gun, etc., the work efficiency will be better.
As an image, it is a shape that floats by applying heat to the red line part.
[iPad Mini 4 LCD Replacement STEP 2]
If the glass is broken, it is not possible to use a suction cup (tool), so insert a spatula into the gap between the liquid crystal and the main body so that it floats.
If you can float the glass part even a little, it is good to put a pick etc. like the image.
If you do this work on one lap of the liquid crystal, you can float the liquid crystal on the whole.
[iPad Mini 4 LCD Replacement STEP 3]
When the liquid crystal floats to some extent, it is possible to lift it like an image, and be sure to lift it from the top (camera side) at this time.
In addition, there is a home button and cable relationship on the lower side, but the home button of the iPad Mini 4 has fingerprint authentication, so please be careful because you will never be able to use fingerprint authentication again if you break it by any chance.
Even if you break it by any chance and perform a home button exchange, the function of fingerprint authentication is paired with the main body side, so you can only use the "normal button" without fingerprint authentication.
[iPad Mini 4 LCD Replacement STEP 4]
It is a scene seen from the front by causing a liquid crystal.
Because there is a connector of the liquid crystal in the lower right part, I will decompose it.
[iPad Mini 4 LCD Replacement STEP 5]
There are three red frames in total, but the leftmost side is the connector of the battery, so please remove it first.
It is a way to remove, but you can easily remove it by using the tool (plastic) and lifting it upward from the bottom.
If you can remove the connector of the battery, let's remove the connector on the liquid crystal side (middle, right side) in the same manner.
[iPad Mini 4 LCD Replacement STEP 6]
Now it was possible to separate the body side and the liquid crystal side.
The removed LCD has a home button, but the home button is implanted into the newly installed liquid crystal.
[iPad Mini 4 LCD Replacement STEP 7]
It becomes the home button part, but please disassemble while paying attention enough because there is a fingerprint authentication function as described earlier.
First of all, i will remove the wiring of the place that is enclosed in red, but you can remove the wiring if you try to wake up because there is a nail on the left side.
All parts except the red frame are only stopped by double-sided tape or bond, but it is necessary to peel off the cable so as not to break.
If you feel a little hard, please apply heat gun or dryer before peeling off.
[iPad Mini 4 LCD Replacement STEP 8]
I was able to remove the home button.
The LCD replacement work is now complete.
LCD replacement and decomposition procedure sianafor iPad Mini 4 8 steps
The lcd of the iPad Mini 4 is easy to remove other than because the glass and the panel are integrated like iPadAir2, Even in the case of glass cracking, it will be replaced by each liquid crystal panel, so it will be more expensive than the model that can only replace the glass.
If the glass is broken, it is not possible to use a suction cup (tool), so insert a spatula into the gap between the liquid crystal and the main body so that it floats.
When the liquid crystal floats to some extent, it is possible to lift it like an image, and be sure to lift it from the top (camera side) at this time.
It is a scene seen from the front by causing a liquid crystal.
There are three red frames in total, but the leftmost side is the connector of the battery, so please remove it first.
Now it was possible to separate the body side and the liquid crystal side.
It becomes the home button part, but please disassemble while paying attention enough because there is a fingerprint authentication function as described earlier.
コメントを残す