How to disassemble and repair the PSP-3000 LCD cracking, screen replacement
Liquid crystal replacement and decomposition procedure of PSP-3000
[LIQUID crystal exchange and decomposition method STEP 1 of PSP-3000]
Start from the place where you can open the cover in the left part of the image.
What is common to all the disassemblies of the PSP-3000 is that you don't need any particularly unusual or expensive tools!
[LIQUID crystal exchange and decomposition method STEP 2 of PSP-3000]
I think that most people have opened this cover once, but please check the meaning of the review.
Because there is a small knob in the image part, you can remove the cover by removing the hook of this part.
[LIQUID crystal exchange and decomposition method STEP 3 of PSP-3000]
There is a battery inside, but you can easily remove it.
PSP It is common to all disassembly, but please be sure to remove the battery before disassembling.
Seal seal on the white arrow part "Please do not peel off this label.Once the product has been peeled off, we refuse to repair any of them.", but if there is no problem because one screw is hidden under this, please proceed with disassembly.
[LIQUID CRYSTAL replacement and decomposition method STEP 4 of PSP-3000]
Remove all four screws in the white circle.
It is possible to remove it easily if there is a thin Phillips screwdriver of the tip.
[LIQUID CRYSTAL replacement and decomposition method step 5 of PSP-3000]
There are screws on the side, so don't forget to remove them.
Because this fine parts become many, it is necessary to manage so as not to lose.
[LIQUID CRYSTAL replacement and decomposition method STEP 6 of PSP-3000]
It is the opposite side of the side, but there are two here, so I will remove it.
[LIQUID CRYSTAL replacement and decomposition method step 7 of PSP-3000]
You can now remove the surface cover, but you can easily remove it by using a tool as shown in the image.
There is a thing that the mark and the volume part of the PlayStation come off on the way, but please proceed without worrying because this is a problem of the structure.
[LIQUID CRYSTAL replacement and decomposition method step 8 of PSP-3000]
I put a tool around the middle and gradually float it, but I think it will come off even if I don't put any special effort into it.
[LIQUID CRYSTAL replacement and decomposition method STEP 9 of PSP-3000]
Only the side of the ✖️ button is fixed with a hook, but it is possible to remove it if it is made to break lightly.
[LIQUID crystal exchange and decomposition method step 10 of PSP-3000]
The surface cover of the PSP-3000 could be removed.
[LIQUID crystal exchange and decomposition method step 11 of PSP-3000]
Because the black nail is fixed to the arrow part of the image, it opens to the outside using the tool.
[LIQUID crystal exchange and decomposition method step 12 of PSP-3000]
I was able to remove it.
[Liquid crystal exchange and decomposition method STEP 13 of PSP-3000]
It becomes the opposite side from the previous, but it can be removed if it makes it to the bottom lightly.
[LIQUID crystal exchange and decomposition method step 14 of PSP-3000]
If you can remove both nails, shift them by about 1cm in the direction of the arrow.
[LIQUID crystal exchange and decomposition method step 15 of PSP-3000]
It is in a state of shifting the liquid crystal panel, but you can see that there is a cable on the lower side.
Because the back side is connected by a cable, i will disassemble the back side this time.
[LIQUID crystal exchange and decomposition method of PSP-3000 STEP 16]
It becomes the back side of the liquid crystal, but you can see that many cables are connected to the connector.
I want to remove the cable of the liquid crystal because it becomes two which is enclosed in a white frame.
[LIQUID crystal exchange and decomposition method step 17 of PSP-3000]
This part should be caused from the back to the front side though it is a place where a spatula (tool) is used to cause a black nail.
[LIQUID crystal exchange and decomposition method step 18 of PSP-3000]
This part is a small connector part next to the previous, but this part should cause a black nail in the opposite direction (front to back) from the previous.
You can remove it if you slide the cable while the nail is raised.
[LIQUID crystal exchange and decomposition method of PSP-3000 STEP 19]
Only the LCD panel was able to be removed from the PSP body.
[LIQUID crystal exchange and decomposition method step 20 of PSP-3000]
An iron plate is attached to the upper side of the liquid crystal, but it can be easily removed by hand.
[LIQUID crystal exchange and decomposition method step 21 of PSP-3000]
I was able to remove the plate.
If you want to change the liquid crystal, you can rearrange it with the original procedure and you will be done.
Liquid crystal replacement and decomposition procedure of PSP-3000
Start from the place where you can open the cover in the left part of the image.
I think that most people have opened this cover once, but please check the meaning of the review.
コメントを残す