How to repair the PSP-3000 stick does not work, does not respond, etc., and how to disassemble it.
PSP-3000 Analog Stick Replacement and Decomposition Procedure
[Analog stick exchange and decomposition method step 1 of PSP-3000]
Start from the place where you can open the cover in the left part of the image.
What is common to all the disassemblies of the PSP-3000 is that you don't need any particularly unusual or expensive tools!
[Analog stick exchange and decomposition method of PSP-3000 STEP 2]
I think that most people have opened this cover once, but please check the meaning of the review.
Because there is a small knob in the image part, you can remove the cover by removing the hook of this part.
[Analog stick exchange and decomposition method step 3 of PSP-3000]
There is a battery inside, but you can easily remove it.
PSP It is common to all disassembly, but please be sure to remove the battery before disassembling.
Seal seal on the white arrow part "Please do not peel off this label.Once the product has been peeled off, we refuse to repair any of them.", but if there is no problem because one screw is hidden under this, please proceed with disassembly.
[Analog stick exchange and decomposition method step 4 of PSP-3000]
Remove all four screws in the white circle.
It is possible to remove it easily if there is a thin Phillips screwdriver of the tip.
[Analog stick exchange and decomposition method of PSP-3000 STEP 5]
There are screws on the side, so don't forget to remove them.
Because this fine parts become many, it is necessary to manage so as not to lose.
[Analog stick exchange and decomposition method step 6 of PSP-3000]
It is the opposite side of the side, but there are two here, so I will remove it.
[Analog stick exchange and decomposition method step 7 of PSP-3000]
You can now remove the surface cover, but you can easily remove it by using a tool as shown in the image.
There is a thing that the mark and the volume part of the PlayStation come off on the way, but please proceed without worrying because this is a problem of the structure.
[Analog stick exchange and decomposition method step 8 of PSP-3000]
I put a tool around the middle and gradually float it, but I think it will come off even if I don't put any special effort into it.
[Analog stick exchange and decomposition method STEP 9 of PSP-3000]
Only the side of the ✖️ button is fixed with a hook, but it is possible to remove it if it is made to break lightly.
[Analog stick exchange and decomposition method of PSP-3000 STEP 10]
The surface cover of the PSP-3000 could be removed.
[Analog stick exchange and decomposition method step 11 of PSP-3000]
Because the black nail is fixed to the arrow part of the image, it opens to the outside using the tool.
[Analog stick exchange and decomposition method step 12 of PSP-3000]
I was able to remove it.
[Analog stick exchange and decomposition method step 13 of PSP-3000]
It becomes the opposite side from the previous, but it can be removed if it makes it to the bottom lightly.
[Analog stick exchange and decomposition method STEP 14 of PSP-3000]
If you can remove both nails, shift them by about 1cm in the direction of the arrow.
[Analog stick exchange and decomposition method STEP 15 of PSP-3000]
It is in a state of shifting the liquid crystal panel, but you can see that there is a cable on the lower side.
Because the back side is connected by a cable, i will disassemble the back side this time.
[Analog stick exchange and decomposition method step 16 of PSP-3000]
It becomes the back side of the liquid crystal, but you can see that many cables are connected to the connector.
I want to remove the cable of the liquid crystal because it becomes two which is enclosed in a white frame.
[Analog stick exchange and decomposition method step 17 of PSP-3000]
This part should be caused from the back to the front side though it is a place where a spatula (tool) is used to cause a black nail.
[Analog stick exchange and decomposition method of PSP-3000 STEP 18]
This part is a small connector part next to the previous, but this part should cause a black nail in the opposite direction (front to back) from the previous.
You can remove it if you slide the cable while the nail is raised.
[Analog stick exchange and decomposition method step 19 of PSP-3000]
Only the LCD panel was able to be removed from the PSP body.
[Analog stick exchange and decomposition method of PSP-3000 STEP 20]
Remove the base of the PSP mark, volume, SELECT, and START buttons.
Because the cable is connected to the connector, it is removed first, but remove the connector of two white frame parts.
[Analog stick exchange and decomposition method step 21 of PSP-3000]
Next, remove one screw next to the analog stick.
After removing the screw, slowly wake up the blue base from the right side to the left side.
[Analog stick exchange and decomposition method step 22 of PSP-3000]
Because there is a nail in the arrow part, please remove it while checking well.
[Analog stick exchange and decomposition method step 23 of PSP-3000]
Next, remove the cable of the cross key, but remove it by raising the nail and sliding it.
[Analog stick exchange and decomposition method step 24 of PSP-3000]
Put the tool on the lower side as shown in the image and peel it off.
[Analog stick exchange and decomposition method step 25 of PSP-3000]
Try to peel off the blue base beside the analog stick.
[Analog stick exchange and decomposition method step 26 of PSP-3000]
The FPC flexible cable is connected to the part under the L button.
[Analog stick exchange and decomposition method step 27 of PSP-3000]
I was able to remove the FPC flexible cable.
[Analog stick exchange and decomposition method of PSP-3000 STEP 28]
I was able to remove the pedestal of the FPC flexible cable.
[Analog stick exchange and decomposition method step 29 of PSP-3000]
There are screws on the left side of the analog stick and cables on the right side, so remove them.
[Analog stick exchange and decomposition method step 30 of PSP-3000]
コメントを残す