If there is a liquid crystal crack or display failure of Fujitsu FMVNFE50B, a liquid crystal panel replacement (LCD replacement) is required!
[Fujitsu FMVNFE50B LCD repair and disassembly method STEP 1]
The display is defective by the screen cracking.
Since it is necessary to change the LCD panel, I would like to disassemble it immediately.
[Fujitsu FMVNFE50B LCD Repair and Decomposition Method STEP 2]
You can remove the battery by turning the console over, but be sure to do this first.
Please note that if you proceed with the disassembly without removing the battery, you may be short-circuited in the middle.
[Fujitsu FMVNFE50B LCD Repair and Decomposition Method STEP 3]
The panel is placed between the rear panel and the frame.
Since the frame itself is fixed with screws, it will be carried out from the work of removing there.
I think that there is no screw just by looking at it, but since there are six screw shatters (rubber) attached to the frame in all, it can be easily peeled off if you turn it around with tweezers etc.
[Fujitsu FMVNFE50B LCD Repair and Decomposition Method STEP 4]
Because the screw is attached to the place which is enclosed in the red frame, I use the Phillips screwdriver.
The screws will be reused later, so please manage them so that they do not disappear.
[Fujitsu FMVNFE50B LCD Repair and Decomposition Method STEP 5]
If the previous screw can be removed, there is no fixed frame, so we will use a tool (spatula) like the image to disassemble it.
If you plug it into the gap between the rear panel and the frame, it will open, so we will do the same work around the LCD.
[Fujitsu FMVNFE50B LCD repair and decomposition method decomposition STEP 6]
If the frame can be removed, I think that the panel is in a bare state, but it cannot be removed because the liquid crystal itself is still fixed.
Remove the screw of the image part, but please do not forget to remove it because there is a screw in the same position on the right side.
[Fujitsu FMVNFE50B LCD Repair and Decomposition Method STEP 7]
I was able to put the panel forward a little bit, but the liquid crystal is attached to the frame of iron called the hinge.
Let's remove all screws because there are four screws on one side!
If you can remove the screw, you can knock the panel forward, but it is easier to work to knock it down to the keyboard side.
[Fujitsu FMVNFE50B LCD Repair and Decomposition Method STEP 8]
The cable is connected to the back of the panel, so you can easily pull it out if you slide it.
I think that only the panel was able to be removed from the laptop body if the decomposition method up to this point was able to be done accurately.
After that, if you replace it with a newly prepared part, the liquid crystal replacement will be completed.
After that, if you replace it with a newly prepared liquid crystal panel, liquid crystal repair of FMV-BIBLO NF/E50 will be completed.
[Fujitsu FMVNFE50B LCD Repair and Decomposition Method STEP 9]
I was able to confirm that it is displayed normally!
Even if the liquid crystal is broken, there is a high possibility that the data remains, so if you replace the liquid crystal as this time, you can use it in the original state, so please refer to it if it breaks down!
If there is a liquid crystal crack or display failure of Fujitsu FMVNFE50B, a liquid crystal panel replacement (LCD replacement) is required!
The panel is placed between the rear panel and the frame.
Because the screw is attached to the place which is enclosed in the red frame, I use the Phillips screwdriver.
If the previous screw can be removed, there is no fixed frame, so we will use a tool (spatula) like the image to disassemble it.
If the frame can be removed, I think that the panel is in a bare state, but it cannot be removed because the liquid crystal itself is still fixed.
I was able to put the panel forward a little bit, but the liquid crystal is attached to the frame of iron called the hinge.
コメントを残す