iPad Pro 10.5 inch LCD replacement is cheap and decomposition method is released

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 1]

Since iPadPro 10.5 inches was able to be obtained just after it was released, i will publish the decomposition method.
As the decomposition difficulty is similar to the previous iPadPro, but I think that almost all parts can be removed if it is possible to remove the liquid crystal of the surface.
Since the liquid crystal panel is fixed as usual with a strong double-sided tape, it is easy to decompose when peeling off while warming.
Let's take it apart!

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 2]

The tools used are Phillips screwdrivers, spatulas, picks, and heat guns (see image).
I think that there is no explanation for those who have used a heat gun, but if you explain it in an easy-to-understand manner to the person who sees it for the first time, is it a powerful version of the dryer?
The reason why the heat gun is used is to make it easy to peel off by warming the double-sided tape.
All of the iPad models are fixed to the frame with double-sided tape, and the LCD needs to be removed no matter which parts are replaced.
This iPadPro 10.5 inch is also fixed to the frame, so I will peel off using this heat gun.

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 3]

It is the position where the heat of the heat gun is applied, but there is a red line (the edge part).
If you apply too much heat, the liquid crystal may burn inside, so keep a reasonable temperature.
Because it becomes an image to pull out with a suction cup (orange) while warming it with heat, the appropriate temperature referred to here is the temperature that floats by pulling the suction cup.

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 4]

Can you see that it floats subtly when I use the suction cup in the place where I applied heat and pull it out?
In the case of an image, it is a float of about 5mm, but it is a good idea to insert a pick etc. if there is a gap even a little.
The iPadPro10.5" has a panel where you plug the pick, so keep the pick depth at about 5mm.

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 5]

I tried to insert a pick near the place where I floated earlier.
If it floats a little like this, the work of inserting the pick is done around the liquid crystal.
It seems to be a lot of work, but this is the only way to peel off the lcd of the iPad.
In addition, because it may break when you try to float the 1cm, 2cm display suddenly, so as to peel off while watching the state.
Since there is a cable only on the home button side, let's peel it off most carefully.

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 6]

I was able to peel off the display.
When the liquid crystal is raised, it should be raised from the camera side, not the home button side.
In terms of the image, the right side is the home button side, but the connector is connected to the logic board, so be careful.

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 7]

I think that you can understand the structure of the iPadPro10.5 if you can cause the liquid crystal overall, so please confirm it.

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 8]

The cable of the liquid crystal is stored in the image part.
The iron plate is fixed with two screws, so let's remove the Phillips screwdriver.

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 9]

When the plate can be removed, the connector appears, but if you lift the arrow part from the bottom to the top, you will be able to remove the connector.
The tool to remove the connector should not be made of metal, but should be used with a pressic spatula.

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 10]

Let's remove the connector in the same manner as before because there is a connector in the same way as two more places when it is possible to remove the previous two places.

[iPad Pro 10.5-inch LCD replacement and decomposition method STEP 11]

The LCD panel could be removed.
As can be said for all iPadPro, the touch panel and the liquid crystal panel are integrated, so it will be a complete replacement just because the glass is broken.
In the same way, if the glass is not broken, but there is a line or a display defect, it will also be replaced by each liquid crystal.
As an emperor removing the LIQUID Crystal, it is up to here, but when replacing parts, a home button transplant is required.